BEEPROG 2 DRIVER
I am using the autoaddressincrement write approach offered by the SST_25 driver functions. I am saying APPROXIMATELY due to my testing results ). if I send 20 bytes, there is 1 error every 15 bytes, if I send 5000 bytes there is one error every 400 bytes. When I reduced the amount of bytes I write, the error increases ( i.e. This error ratio is when I Write 1000 bytes. I have set up a compare function to compare the byte written to the SPI and read from the SPI. The error is approximately 1 wrong byte per 200 bytes. © Copyright 2003 - 2009 Mcumall Electronics Inc.Hello I am using: -pic32mx795f512l -sst25vf016b -SPI baud rate 1MHz (I have tried 1-10MHz) -Master mode -Enhanced buffer -Interrupt priority 1 -sub-Interrupt priority 0 -8-bit data width -Idle low edge rise flash functions I'm having very inconsistent writing to my SPI Flash. Yes but the BeeProg2C can test TTL/CMOS logic ICs and memories as well. I am currently using the Wellon VP990 and i am thinking of buying the VP998 or the Beeprog2C from Elnec If you don't want to use this brand anymore, which other powerful programmer would you recommend instead? Is it not possible to use universal adapters on the Elnec Beeprog2c ? Not very cool from Elnec, it seems they want to make money on selling adapters. In these conditions if i am asked I can make only negative advertise for ELNEC policy and products. There are actual memories that are used on the market today but were probably produced about 10 years ago.Īs a personal opinion, to buy an original ELNEC Beeprog is more of a scam than buying a Chinese clone of the product! If you want to buy the program honestly and correctly you are taken as a fool! In the short list you will see that it in not about antique memories (i.e. (Admit I made the mistake of quickly selling old Lab Prog).
BEEPROG 2 UPGRADE
I put down a brief list of some circuit that I have not actually been able to access due to lack of adapters, memory that you have read successfully with old Lab Prog using a universal adapter ( the complete list is very long though).īelieve me that was I placed in embarrassing situations with the client for which I had to deny or postpone his service on the same equipment that i serviced one year ago! the client does not understand what kind of upgrade I made so that now i can’t serve him!!!. (I never allowed him to compare with Hobbist site for the Willem Willem I managed to read some of the memories attached list). The fact is that currently can not use Beeprog 2C than at the level of "ponyprog" without making an investment of a few hundred euros. Honestly now I'm going to buy me another programmer Although I considered myself a original ELNEC fan for almost 20 years. I didn’t find on the ELNEC site a list to present assigned to each adapter the specialized kind of memory that can be accessed, in order to buy the most common adapters instead of the more specialized ones. lack of a minimum package of specialized adapters that the programmer can use a "low cost" $ 100 Ħ. Using the option "Quick!" 2-5 days (real 7-10 days) has much higher costs!ĥ.
BEEPROG 2 SOFTWARE UPGRADE
The trend is that for every memory you need to buy special adapter for any software upgrade you are surprised to read you can not access the same memory acessed one month before with the same programmer unless you buy a special adapter Ĥ. The cost on the new adaptor is very high compared with the program (between 10-30% of the program value).ģ. when you buy the program you are not aware of the new business strategy Ģ. I belive that the new market policy of ELNEC is not correct towards the clients:ġ. ( The new adapters are protected with Dallas DS2432, do not try to read this Dallas with Beeprog because destroy the adapter )
BEEPROG 2 SERIAL
Also, for some serial flash with 8 pins you have to buy adapters- it works without on Seeprog but you have to buy one with Beeprog 2C. Moreover, for a lot of integrated circuits you have to buy 2 adapters. I was surpised to find out that in order to access a memory type whcic has 10-15 years i have to buy an specialized adaptor which cost about 10-20% of the program. I expected that the new product will continue the job done by the old one without new charges. I was very disappointed by the acquisition. I have renounced at the old LabProg 48LV (firstly bought) and I bought the Beeprog 2C from the same producer. Half of year passed since I made an upgrade on the ELNEC program. True USB Willem Programmer (GQ-2X, GQ-3X, GQ-4X) MCUmall EPROM BIOS Chip Burner Forum - New Beeprog 2 disappointment
0 kommentar(er)
